[PDF&VCE] Updated 300-101 New Questions From Lead2pass Free Downloading (184-194)
2016 November Cisco Official New Released 300-101 Dumps in Lead2pass.com!
100% Free Download! 100% Pass Guaranteed!
After purchasing the dumps for the 300-101 Exam from Lead2pass, I had no doubt that I’d easily pass the exam. Bundle of thanks to Lead2pass for helping me pass the exam without any troubles.
Following questions and answers are all new published by Cisco Official Exam Center: http://www.lead2pass.com/300-101.html
What command can you enter to configure an enable password that uses an encrypted password
from another configuration?
A. enable secret $abc%!e.Cd34$!ao0
B. enable secret 7 Sabc%!e.Cd34$!ao0
C. enable secret 0 Sabc%U*.Cd34$!ao0
D. enable secret 5 $abc%!e.Cd34$!ao0
E. enable secret 15 $abc%ie.Cd34$!ao0
F. enable secret 6 $abc%!e.Cd34$!ao0
A network engineer receives reports about poor voice quality issues at a remote site.
The network engineer does a packet capture and sees out-of-order packets being delivered.
Which option can cause the VOIP quality to suffer?
A. traffic over backup redundant links
B. misconfigured voice vlan
C. speed duplex link issues
D. load balancing over redundant links
In traditional packet forwarding systems, using different paths have varying latencies that cause out of order packets,
eventually resulting in far lower performance for the network application. Also , if some packets are process switched quickly by the routing engine of the router while others are interrupt switched (which takes more time)
then it could result in out of order packets. The other options would cause packet drops or latency, but not out of order packets.
What is the administrative distance for EBGP?
Considering the IPv6 address independence requirements, which process do you avoid when you use NPTv6 for translation?
A. rewriting of higher layer information
B. checksum verification
C. ipv6 duplication and conservation
D. IPSEC AH header modification
The IPv6-to-IPv6 Network Prefix Translation (NPTv6) serves as a useful mechanism for implementing address independence in an IPv6 environment. A major benefit associated with NPTv6 is the fact that it avoids the requirement for an NPTv6 Translator to rewrite the transport layer headers which reduces the load on network devices
What is the optimal location from which to execute a debug command that produces an excessive
amount of information?
A. Vty lines
B. SNMP commands
C. A console port
D. An AUX port
A network engineer is configuring the router for NetFlow data exporting.
What is required in order
for NDE to begin exporting data?
B. Flow mask
D. Interface type
E. Traffic type
F. NetFlow version
NetFlow Multiple Export Destinations–To configure redundant NDE data streams, which improves the probability of receiving complete NetFlow data, you can enter the ip flow-export destination command twice and configure a different destination IP address in each command. Configuring two destinations increases the RP CPU utilization, as you are exporting the data records twice.
A. Encapsulation is mismatched.
B. Frame Relay map is configured.
C. DLCI is active.
D. DLCI is inactive or deleted.
E. An access list is needed to allow ping
Frame Relay: Cannot ping Remote Router :
1-Encapsulation mismatch has occurred.
2-DLCI is inactive or has been deleted.
3-DLCI is assigned to the wrong subinterface.
4-An access list was misconfigured.
5-The frame-relay map command is missing.
6-No broadcast keyword is found in frame-relay map statements.
At which layer does Cisco Express Forwarding use adjacency tables to populate addressing
B. Layer 2
C. Layer 1
D. Layer 3
Adjacency table – Nodes in the network are said to be adjacent if they can reach each other with a single hop across a link layer. In addition to the FIB, CEF uses adjacency tables to prepend Layer 2 addressing information. The adjacency table maintains Layer 2 next-hop addresses for all FIB entries http://www.cisco.com/c/en/us/support/docs/routers/12000-series-routers/47321-ciscoef.html
A network engineer wants to ensure an optimal end-to-end delay bandwidth product. The delay is
less than 64 KB. Which TCP feature ensures steady state throughput?
A. Window scaling
B. Network buffers
C. Round-trip timers
D. TCP acknowledgments
options can be carried in a TCP header. Those relevant to TCP performance include Window-scale option : This option is intended to address the issue of the maximum window size in the face of paths that exhibit a high-delay bandwidth product. This option allows the window size advertisement to be right-shifted by the amount specified (in binary arithmetic, a right-shift corresponds to a multiplication by
2). Without this option, the maximum window size that can be advertised is 65,535 bytes (the maximum value obtainable in a 16-bit field). The limit of TCP transfer speed is effectively one window size in transit between the sender and the receiver. For high-speed, long-delay networks, this performance limitation is a significant factor, because it limits the transfer rate to at most 65,535 bytes per round-trip interval, regardless of available network capacity. Use of the window-scale option allows the TCP sender to effectively adapt to high-band-width, high-delay network paths, by allowing more data to be held in flight.
The maximum window size with this option
A network administrator creates a static route that points directly to a multi-access interface, instead of the next-hop IP address. The administrator notices that Cisco Express Forwarding ARP requests are being sent to all destinations. Which issue might this configuration create?
A. Low bandwidth usage
B. High memory usage
C. Cisco Express Forwarding routing loop
D. High bandwidth usage
E. IP route interference
A. only accepts time requests from 192.168.1.1
B. only handle four requests at a time
C. only is in stratum 4
D. only updates its time from 192.168.1.1
E. only accepts time requests from 192.168.1.4
F. only updates its time from 192.168.1.4
IOS router defines the following four types of access for NTP:
1) Peer – permits router to respond to NTP requests and accept NTP updates. NTP control queries are also accepted. This is the only class which allows a router to be synchronized by other devices.
2) Serve – permits router to reply to NTP requests, but rejects NTP updates (e.g. replies from a server or update packets from a peer). Control queries are also permitted.
3) Serve-only – permits router to respond to NTP requests only. Rejects attempt to synchronize local system time, and does not access control queries.
4) Query-only – only accepts NTP control queries. No response to NTP requests are sent, and no local system time synchronization with remote system is permitted.
I understood all of the questions very easily. I scored 96% on my first try. I am definitely going to spread the word amongst friends and colleagues. Keep up the great work.
300-101 new questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDZVhTdmV3Z1kwc2c
2016 Cisco 300-101 exam dumps (All 230 Q&As) from Lead2pass:
http://www.lead2pass.com/300-101.html [100% Exam Pass Guaranteed]