[Full Version] 100% Pass 640-916 Exam By Training Lead2pass New VCE And PDF Dumps (141-160)
2016 November Cisco Official New Released 640-916 Dumps in Lead2pass.com!
100% Free Download! 100% Pass Guaranteed!
Lead2pass dumps for 640-916 exam are written to the highest standards of technical accuracy, provided by our certified subject matter experts and published authors for development. We guarantee the best quality and accuracy of our products. We hope you pass the exams successfully with our practice test. With our Cisco 640-916 dumps, you will pass your exam easily at the first attempt. You can also enjoy 365 days free update for your product.
Following questions and answers are all new published by Cisco Official Exam Center: http://www.lead2pass.com/640-916.html
What two options are performed during initial setup of a UCS Manager? (Choose two.)
A. Configuring Nodes
B. Configuring Servers
C. Configure Routing
D. Configure Equipment Policy
E. Configure Ports
What two options are key features for UCSM Manager? (Choose two.)
A. Policy Based Management
B. Manual Discovery
C. Firmware provisioning
D. Low Availability
E. Supports Fabric-Path
Refer to the exhibit. An engineer has configured a primary fabric interconnect with this configuration. Which two pieces of information are needed to guarantee high availability and fail over for the secondary fabric interconnect for the cluster? (Choose two.)
Which two models of Cisco WAAS can be integrated into the Cisco 4000 Series ISR routers? (Choose two.)
B. vWAAS on Cisco UCS E-Series
C. WAAS Express Cisco UCS E-Series
D. vWAAS on Cisco UCS B-Series
Which two common issues in the data center are addressed by Cisco Wide Area Application Services? (Choose two.)
A. provide branch office employees LAN-like access to information
B. migration of data servers into core data center
C. minimize LAN bandwidth consumption
D. higher rates of packet loss over the WAN
E. reduced core data center server requirement
What are three advantages to running FabricPath in the data center over using Spanning Tree? (Choose three.)
A. provides multichassis EtherChannel capabilities
B. improves convergence times
C. uses TTL field to provide loop mitigation
D. allows every switch to send BPDUs to each other to ensure the L2 topology is synchronized
E. has L2 multipath forwarding capabilities
F. uses 802.1q trunks to ensure VLANs are propagated through the topology
A company is considering unifying the data center fabrics.
What two technologies will allow IP traffic and the Fibre Channel to run over the same fabric? (Choose two.)
A. Rapid Spanning Tree
B. Fibre Channel over Ethernet
C. Overlay Transport Virtualization
D. Data Center Bridging Exchange Protocol
Refer to the exhibit. A network engineer proposes a hierarchical network design for building a company’s campus network as shown.
What are three advantages of this approach? (Choose three.)
A. offers a hierarchy in which all layers share similar roles
B. offers a hierarchy in which each layer has a specific role
C. offers a modular topology with segregated building blocks
D. offers a flat topology with integrated building blocks
E. promotes a network virtualization traffic pattern
F. creates small fault domains with clear demarcations and isolation
A storage engineer has a new requirement to have control plane and data plane separation between the financing and student storage pools.
What SAN technology can be used to facilitate this?
B. Zone Sets
D. Port Security
A. It runs at 10 Gbps.
B. It is part of a logical port channel interface.
C. It is configured as a point-to-point interface.
D. It is administratively down.
E. It uses a nonstandard MTU size.
Customer is configuring FCoE and NPV in their Data Center on Cisco Nexus 5000 Series Switches. Please go through the Topology and Exhibit 1 through 4 to answer the following questions.
A. In this scenario disruptive load balancing is disabled.
B. In this scenario disruptive load balancing is enabled.
C. Since FCID: 0x1c0000 is reserved, disruptive load balancing is not configured correctly.
D. When disruptive load balancing is enabled, NPV redistributes the server interfaces across all available NP uplinks when a new NP uplink becomes operational. To move a server interface from one NP uplink to another NP uplink, NPV forces reinitialization of the server interface so that the server performs a new login to the core switch.
Which statement describes multihop FCoE function when an FCoE switch receives an FCoE frame from the directly connected FCoE host?
A. The switch receives the FCoE frame and forwards it to another switch over its VE port.
B. The switch receives the FCoE frame, deapsulates it, and sends the Fibre Channel frame to the
fabric over its Fibre Channel uplink port.
C. The switch receives the FCoE frame, deapsulates it, and sends the Fibre Channel frame to the
Fibre Channel target over its Fibre Channel port.
D. The switch receives the FCoE frame and forwards it to another FCoE device over its VN port.
Which two statements about SAN port channels configured on Cisco Nexus 5000 Series switches are true? (Choose two.)
A. The bring up protocol automatically detects and overrides any misconfiguration.
B. You can manually configure channel groups, or they can be automatically created.
C. Changes in configuration to the SAN port channel interface must also be made to all members
of the channel group.
D. The port channel protocol uses the exchange fabric parameters command to communicate across
peer ports in an ISL.
E. The port channel protocol ensures that a set of ports is eligible to be part of the same SAN port channel.
Refer to the exhibit. A customer has connected ports from a Cisco UCS 6296 using factory default settings, in this way:
– Ports 45-48 connected to an upstream Cisco MDS switch
– Ports 16-19 connected to an upstream Cisco Nexus 5596 switch
Which two port modes should be used in Cisco UCS Manager? (Choose two.)
A. ports 45-48 as Fibre Channel uplink ports
B. ports 16-19 as uplink ports
C. ports 45-48 as Fibre Channel storage ports
D. ports 16-19 as server ports
E. ports 45-48 as FCoE ports
A user is trying to create a new VDC in NX-OS in global configurations mode, but receives an error message. What issue prevents the user from creating Virtual Device Contexts?
A. The user is not granted Super User role permissions.
B. VDCs cannot be created in NX-OS.
C. The user is not a member of VDC Power Admin group.
D. VDCs are not created under interface configurations mode.
Which Cisco Nexus 1000V component provides the platform on which Cisco NX-OS runs and interacts with other components that make up the Cisco Nexus 1000V?
A. Virtual Supervisor Module
B. Virtual Ethernet Module
C. Virtual Service Blade
D. Virtual Security Gateway
What native Fibre Channel technology facilitates connecting multiple Fibre Channel devices behind a single FC address?
A. N-Port Virtualization
B. N-Port Identification Virtualization
C. Fibre Channel Arbitrary Loop
D. Fiber Channel over Ethernet
Which requirement is unique to service profile templates?
C. pooled identities
We offer standard exam questions of Cisco 640-916 dumps. The standard exams are important if you have never taken a real exam. The accuracy of the Q&As are fully guaranteed and the number is enough to impact you passing the exam.
640-916 new questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDd252MVQ5dGl0Smc
2016 Cisco 640-916 exam dumps (All 191 Q&As) from Lead2pass:
http://www.lead2pass.com/640-916.html [100% Exam Pass Guaranteed]